Published on Apr 9, 2017
A 1978 P&H 2800 Mark II equipped with an XP Series boom loading a fleet of Komatsu-Dresser 830E mining trucks.
Like mining? Then join the PAmining today! https://www.facebook.com/PAmining-164...
Published on Apr 8, 2017
I took some video of Grandpa's auction today. This is his second auction he had one yrs ago when he quit doing construction. Now that he has quit doing excavating work he got rid of some more things. He sells his Ford Golden Jubilee, His Ford Diesel pickup, and his tri axle trailer in the video. He sold all kinds of other stuff including his case dozer but I didn't get that on film. I don't like to stick my hand in the air at action! lol He has totally redone his Ford Jubilee Tractor and boy was it sharp. The 99 Ford f250 with the 7.3 went cheap. The body wasn't in the best shape bit it had under 150,000 miles on it. The tri axle trailer was in good condition as well. Kinda different vid today!
Published on Apr 11, 2017
We went to Detroit Diesel Factory and got to see a few things! The Detroit Diesel Factory was a very impressive shop, no dirt to be found! We run the Detroit Diesel DD16 in 3 of our Frieghtliner Trucks. These Frieghtliners are built strong for the woods. They also build the DD 15, DD13, DD8 and the DD5. All these Detroit's are very nice motors. They also build the DD12 transmission there as well. The new transmission is a very nice setup that Detroit is doing. The new DD5 engine looks very very impressive and is getting very good milage on some test trucks. It will be interesting to see when those motors come out.
Published on Apr 12, 2017
This is how to roll a skidder! Josh shows just what it looks like when the skidder starts to roll. Josh felt the skidder quick and let off the winch, if he was to keep pulling the truck she would have rolled over. The Cat escaped unharmed and we got the stuck Frieghtliner out of the mud. The truck got in a hole on the passenger side and it didn't come out easy. Took both Cat 535D Skidders to get it rolling again. The chip van had a little bit of a lean going on, always thinking about those things tipping over too, they are very top heavy.
Just Keep Rollin'
Published on Apr 13, 2017
This is how I just about lost the end of my finger! I was working on the Morbark chipper and this accident happened. It was a real close call. Simply put I put my finger where it should not have been. I didn't lose my finger so that's good!! It hurt!! I'm going to be just fine..Just Keep Rollin'
Published on Apr 15, 2017
Why is it that the Chipper always seems to break in the rain....or when it's snowing!! The conveyor broke and almost had a big mess on our hands but I caught it just in time. The Morbark Chipper broke and we didn't get if fixed right away. It broke last Thursday and then we went to Detroit Diesel on Friday then the weekend came so we didn't get it fixed till Monday. It's time I start catching up on some videos. Thanks so much for Watching
Wisconsin Farm Equipment Dealer Traces History Back to 1931 Machinery Pete
Published on Apr 14, 2017
Machinery Pete interviews Waldo Riesterer with Riesterer & Schnell, a 12-store John Deere dealership in Wisconsin. Pete and Waldo talk at their Chilton, WI store about the company's amazing 86 year history dating to 1931, a history that at one included a tavern at the dealership
Published on Apr 16, 2017
I finally had some time to clean the tool truck. The tool truck got really bad and somehow I always have to clean it....I do make a mess in there I must admit. Haha Cleaning it took over an hour, but Mike did show up on his quad and I talked to him for about ten minutes. The tooly got a good cleaning thanks to That Chipper Guy!! It still a little attention but it is much much cleaner!! Let's put away some tools! Just Keep Rollin'
Published on Apr 17, 2017
The White Kenworth hit a pine tree, and I blew a tire on the tool truck! Just another day in the woods. Took some work to get the white truck out due to the broken front end but we got it out. Had to do some pulling on the trailer to get it around the corner. Then the tool truck blew a tire when I went to go run the old Morbark Chipper. Had to run to the shop to get some new tires out on.
Published on Apr 19, 2017
Had to move some dirt with the cat D6 so the chipper could get set up. The trail needed some work and the landing needed touched up. The ditch out front needed some work and that will get removed when we leave. The Caterpillar D6 Dozer can move some serious dirt. Paul also had the Caterpillar 535D skidder working the ground as well. With the skidder and dozer we can do some work. Hope y'all enjoy!
Published on Apr 20, 2017
The new Cat 374F LME excavator loading the new Caterpillar 772G mining dump truck, with the new Cat 988K wheelloader waiting in the background, in Europe's largest basalt quarry in Homberg Germany, at the Stein Expo 2014 mining trade fair.
John Deere 2750 Hard Starting Issue - Starter & Water Pump Trials & Tribulations afleetcommand
Published on Apr 22, 2017
John Deere 2750 and many of the tractors with that same motor / hydraulic pump setup can be tough to get started as they age. The motor wears, the batteries and starter motor get some age on them. Pretty common issue. SO no surprise when mine exhibited those same characteristics. It was even hard to get going in the summer! Forget the colder fall and winter season! HAD to either solve the issue or get rid of that tractor.
Published on Apr 23, 2017
Komatsu PC240 dash 10 excavator feeding the Kleemann Mobirex MR 130 Z EVO 2 impact crusher, with an Liebherr L556 2Plus2 wheelloader removing the crushed materials from under the conveyor, at the E&H '15 expo in Denmark.
Published on Apr 27, 2017
The big 1500 HP Leopard 2 tank leaving the tractor pulling arena, and is loaded on to a trailer, after pulling the Black Devil sledge @ Allingåbro motor festival 2014 in Denmark.
Published on Apr 27, 2017
The bark is starting to slip up here in Michigan! This makes it much easier to get a clean chip out of this flail chipper. We use less chain and fuel this time of year!! Makes my job a little easier. This chipper can clean the bark off quite nicely when the bark slips. hope y'all enjoy!
Published on Apr 30, 2017
Time to change some speed sensor and transducers!! I had to change two speed sensors and two transducers on the Morbark Chipper!! The speed sensor's where for the flail drums. The transducers where for the bottom outfeed pressure, and the first yoke wheel pressure. Working on this wood chipper is always interesting so I hope you enjoy!
How To Rebuild A Diesel Engine Part 4. Deck Prep, Piston Packs, And Rod Bearings. Cat C13. Adept Ape
Published on Apr 30, 2017
The fourth installment of this series has the rest of the rotating assembly being installed, which includes the cylinder packs. The cleaning of the cylinder block deck is also shown with how to prep it for the installation of the cylinder head. Donations to the channel can be sent to AdeptApe@yahoo.com on Paypal. Thank you for watching the video.
Published on Apr 30, 2017
Our friend Niels is trying the new Cat 926 M series wheel loader, moving some crushed asphalt around, @ the Pon-Cat and Mercedes open house event in a gravel pit in Denmark :)
Huge construction project for building more lanes on the highway. Heavy machinery working hard every day to finish the project on schedule. The highway will be transformed into a tunnel to reduce the noise.
Tearing down a former office building in downtown with a nearby river and residential buildings. The massive Hitachi Zaxis 870 longfront demolition excavator is equipped with a telescopic boom, extendable up to 50 meters!
Machines in this video:
- Hitachi Zaxis 870 longfront crawler excavator
- Caterpillar 345C longfront crawler excavator
- Caterpillar 336E crawler excavator
- Liebherr LTM mobile crane